drahoslav.d
Posts: 4
Joined: May 08, 2018 2:48 pm
Contact: Send private message

Nejde nahrát nový firmware ale starší ano

Feb 11, 2019 10:27 am

Zdravím, udělal jsem upgrade z MK2 na MK2.5 MM2 a mám problém s nahráním firmware. Desku mám RAMBo13a. Aktualizace firmware dělám pomocí Slic3r PE - nahrát firmware tiskárny.

Do MM to šlo bez problému. Do ramba jdou bez problému verze na MK2. Na MK2.5 jde nahrát pouze verze 3.1.4. Jakákoliv novější verze už nejde.

Log verze 3.1.4

Code: Select all

avrdude: Version 6.3-20160220-prusa3d, compiled on Nov 22 2018 at 15:22:47 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "D:/Winprog/Prusa3D/Slic3rPE/resources\avrdude\avrdude.conf" Using Port : COM3 Using Programmer : wiring Overriding Baud Rate : 115200 AVR Part : ATmega2560 Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 10 8 0 no 4096 8 0 9000 9000 0x00 0x00 flash 65 10 256 0 yes 262144 256 1024 4500 4500 0x00 0x00 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : Wiring Description : Wiring Programmer Model: AVRISP Hardware Version: 15 Firmware Version Master : 2.10 Vtarget : 0.0 V SCK period : 0.1 us avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e9801 (probably m2560) avrdude: safemode: hfuse reads as D8 avrdude: safemode: efuse reads as FD avrdude: reading input file "D:\Winprog\Prusa3D\prusa3d_fw_mk25-3.1.4.330.201804091650.hex" avrdude: writing flash (228236 bytes): avrdude: stk500v2_command(): command failed Writing | ################################################## | 100% 40.63s avrdude: 228236 bytes of flash written avrdude: verifying flash memory against D:\Winprog\Prusa3D\prusa3d_fw_mk25-3.1.4.330.201804091650.hex: avrdude: load data flash data from input file D:\Winprog\Prusa3D\prusa3d_fw_mk25-3.1.4.330.201804091650.hex: avrdude: input file D:\Winprog\Prusa3D\prusa3d_fw_mk25-3.1.4.330.201804091650.hex contains 228236 bytes avrdude: reading on-chip flash data: Reading | ################################################## | 100% 29.23s avrdude: verifying ... avrdude: 228236 bytes of flash verified avrdude: safemode: hfuse reads as D8 avrdude: safemode: efuse reads as FD avrdude: safemode: Fuses OK (E:FD, H:D8, L:FF) avrdude done. Thank you.

Log verze 3.5.1

Code: Select all

avrdude: Version 6.3-20160220-prusa3d, compiled on Nov 22 2018 at 15:22:47 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "D:/Winprog/Prusa3D/Slic3rPE/resources\avrdude\avrdude.conf" Using Port : COM3 Using Programmer : wiring Overriding Baud Rate : 115200 AVR Part : ATmega2560 Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 10 8 0 no 4096 8 0 9000 9000 0x00 0x00 flash 65 10 256 0 yes 262144 256 1024 4500 4500 0x00 0x00 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : Wiring Description : Wiring Programmer Model: AVRISP Hardware Version: 15 Firmware Version Master : 2.10 Vtarget : 0.0 V SCK period : 0.1 us avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e9801 (probably m2560) avrdude: safemode: hfuse reads as D8 avrdude: safemode: efuse reads as FD avrdude: reading input file "D:\Winprog\Prusa3D\prusa3d_fw_MK25_3_5_1_RAMBo13a_en-cz.hex" avrdude: writing flash (222386 bytes): avrdude: stk500v2_command(): command failed Writing | #######avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x13 avrdude: stk500v2_paged_write: write command failed avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x06 avrdude: stk500v2_loadaddr(): failed to set load address ***failed; ########################################### | 100% 26.36s avrdude: failed to write flash memory, rc=-1 avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x18 avrdude: stk500isp_read_byte(): timeout/error communicating with programmer avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x18 avrdude: stk500isp_read_byte(): timeout/error communicating with programmer avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x18 avrdude: stk500isp_read_byte(): timeout/error communicating with programmer avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x18 avrdude: stk500isp_read_byte(): timeout/error communicating with programmer avrdude: safemode: Sorry, reading back fuses was unreliable. I have given up and exited programming mode avrdude: stk500v2_recv(): timeout avrdude: stk500v2_recv(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer avrdude: stk500v2_command(): failed miserably to execute command 0x11 avrdude: stk500v2_disable(): failed to leave programming mode avrdude done. Thank you.


Hledal jsem na netu a podle rad jsem zkoušel měnit USB porty i kabely. Vyzkoušel jsem i různé počítače. COM mám určitě nastavený dobře, protože by nešli nahrát staré verze. Nesetkal jste se s tím někdo?

Dík předem za odpověď

vaclav.h8
Posts: 2
Joined: Dec 08, 2018 7:28 am
Contact: Send private message

Re: Nejde nahrát nový firmware ale starší ano

Feb 13, 2019 6:37 pm

Mám taky problém s nahráním nového firmware do MK3, jak tento problém odstranit, poslední nahraný firmware mám 3.5.0-1749

avrdude: Version 6.3-20160220-prusa3d, compiled on Feb 11 2019 at 18:25:11
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:/PROGRA~1/Prusa3D/Slic3rPE/resources\avrdude\avrdude.conf"

Using Port : COM3
Using Programmer : wiring
Overriding Baud Rate : 115200

avrdude done. Thank you.

Problém vyřešen :D :D :D :D
MK3 připojena k stolnímu počítači na základní desku USB2 a vše začalo fungovat.

Return to “Hardware, firmware a software (Pomoc)”

Who is online

Users browsing this forum: No registered users and 1 guest