Search found 72 matches

Go to advanced search

by Kolous
Mar 19, 2019 5:55 pm
Forum: General discussion, announcements and releases
Topic: Firmware 3.7.0-RC1 for Original Prusa i3 MK2.5S & MK2.5
Replies: 13
Views: 408

Re: Firmware 3.7.0-RC1 for Original Prusa i3 MK2.5S & MK2.5

I've only done a quick test with 7x7 bed levelling, 3 measurements and mag compensation. I stopped it though, because it looked (and sounded) like the x-axis ramming into the endstop before beginning the bed levelling. It finishes though successfully. Did anyone else have this experience with the n...
by Kolous
Mar 19, 2019 9:18 am
Forum: General discussion, announcements and releases
Topic: Firmware 3.7.0-RC1 for Original Prusa i3 MK2.5S & MK2.5
Replies: 13
Views: 408

Re: Firmware 3.7.0-RC1 for Original Prusa i3 MK2.5S & MK2.5

The 7x7 bed leveling is amazing, just tested a whole bed plane yesterday and 1st layer is consistent now. Pitty you didn't release it one week earlier when I was printing quite large stand ;)
by Kolous
Mar 14, 2019 6:30 am
Forum: Nejlepší výtisky & tiskové tipy
Topic: RC funkční ponorka třída 214 1/72 s 3D tisku
Replies: 40
Views: 6409

Re: RC funkční ponorka třída 214 1/72 s 3D tisku

Ty ponorky jsou fakt parádní. Je to pěkný doplnění k 3D tištěnejm letadlům. Jsem koukal na Vašem webu, že prodáváte kity s kompletními díly. Tady má každej svou tiskárnu a mě osobně baví si model vytisknout před složením sám. Uvažujete i o kitech pouze se všemi HW součástkami? Ten bych si pořídil.
by Kolous
Feb 18, 2019 10:05 am
Forum: Nejlepší výtisky & tiskové tipy
Topic: CJUZ - Fallout anti material rifle
Replies: 2
Views: 448

Re: CJUZ - Fallout anti material rifle

Pěkná práce....talent ;)
by Kolous
Jan 30, 2019 3:23 pm
Forum: Hardware, firmware a software (Pomoc)
Topic: Bug firware 3.5.0/3.5.1
Replies: 2
Views: 95

Re: Bug firware 3.5.0/3.5.1

Potvrzuju. Pozoroval jsem chybu, když jsem tiskl několikrát po sobě a přerušil tisk. Při pohybu v menu SD karty se tiskárna zblázní a vozík X začne tlačit do pravé strany.
by Kolous
Jan 22, 2019 5:03 pm
Forum: General discussion, announcements and releases
Topic: MMU2 - Real Multi Material
Replies: 51
Views: 2249

Re: MMU2 - Real Multi Material

nikolai.r wrote:
Jan 21, 2019 5:53 pm
Based on my experience small strings are not a problem if FINDA is set right.
Finda is triggered as it should. But the strings stockpile so after 100 +- changes it got jamed.
by Kolous
Jan 21, 2019 5:49 pm
Forum: General discussion, announcements and releases
Topic: MMU2 - Real Multi Material
Replies: 51
Views: 2249

Re: MMU2 - Real Multi Material

Negative.....still stringing :?
by Kolous
Jan 20, 2019 4:17 am
Forum: Assembly and first prints troubleshooting
Topic: MMU2 impact on flow?
Replies: 2
Views: 112

Re: MMU2 impact on flow?

Hello, no issues with up to 0,2 layer height. But I had issues with 0,35 and 0,2 100mm/s where there was obviously not enough material passing through the HE. So when I print single color on this profiles I just remove the orange tube, put bit of fillament into FINDA (so it doesn't initialize), move...
by Kolous
Jan 19, 2019 6:19 pm
Forum: General discussion, announcements and releases
Topic: MMU2 - Real Multi Material
Replies: 51
Views: 2249

Re: MMU2 - Real Multi Material

Great ;-) I'm currently printing this thing since noon parsed with your script: P_20190119_190013.jpg PLA Plasty Mladeč and Filamentum 205°C and Verbatim BVOH 195°C. But still stuggling with the BVOH tips: P_20190119_185900.jpg This is the best I could get so far. All values default just increased c...
by Kolous
Jan 19, 2019 9:08 am
Forum: General discussion, announcements and releases
Topic: MMU2 - Real Multi Material
Replies: 51
Views: 2249

Re: MMU2 - Real Multi Material

Can you add to the program to put a remark into the gcode header that the file was processed with mmuGcodeParser version X. So after some time passes I can check what the file stored on the card actually is?

Go to advanced search