Search found 687 matches

Go to advanced search

by josefprusa
Fri Jun 23, 2017 2:30 pm
Forum: Rady k tisku - Nastavení Slic3ru, KISSliceru, oprava modelů, ...
Topic: Oddelene vrstvy
Replies: 4
Views: 299

Re: Oddelene vrstvy

Chtělo by to fotku. Nicméně spíš mi příjde, jestli je v tiskárně správný materiál. PLA se samo od sebe nedelaminuje.
by josefprusa
Fri Jun 23, 2017 2:29 pm
Forum: Rady k tisku - Nastavení Slic3ru, KISSliceru, oprava modelů, ...
Topic: Náhly posun tisku
Replies: 4
Views: 205

Re: Náhly posun tisku

Dobry den, a proc nepouzivate predkonfigurovany Slic3r z nasich ovladacu? Pravdepodobne je neco spatne nastavene ve vasem profilu pro Kisslicer.
by josefprusa
Fri Jun 23, 2017 2:25 pm
Forum: Original Prusa i3 MK2
Topic: Did everyone get their orders on time?
Replies: 825
Views: 44068

Re: Did everyone get their orders on time?

Increasing the production of fully assembled by 20 a day is quite easy and did wonders with the backlog. However increasing the production by the same number with kits would do nothing with the leadtimes. We increased production of everything, but only fully assembled have seen such a dramatic effec...
by josefprusa
Fri Jun 23, 2017 10:32 am
Forum: Original Prusa i3 MK2 Multi Material
Topic: stringing after MM upgrade
Replies: 9
Views: 554

Re: stringing after MM upgrade

You need to slice with the correct settings. Single extruder mode is in the normal MK2 Slic3r. Sample g-codes form the SD card cannot be used.
by josefprusa
Tue May 02, 2017 1:13 pm
Forum: Síň slávy - Nejlepší výtisky
Topic: tisk po upgrade na 1.75 :)
Replies: 61
Views: 11409

Re: tisk po upgrade na 1.75 :)

Dobra prace :!:
by josefprusa
Thu Feb 23, 2017 4:49 pm
Forum: Original Prusa i3 MK2
Topic: Error while upgrading to 3.0.9
Replies: 6
Views: 351

Re: Error while upgrading to 3.0.9

Can you try updated version for OSX Sierra? http://www.prusa3d.com/downloads/firmwa ... v2_1_b.zip

They changed some privileges and it broke the updater :-/ but we found a workaround!
by josefprusa
Sat Feb 04, 2017 11:35 am
Forum: Original Prusa i3 MK2
Topic: New 3.0.10-RC1 firmware for Prusa i3 MK2
Replies: 36
Views: 3615

Re: New 3.0.10-RC1 firmware for Prusa i3 MK2

Loose pulley doesn't have to do anything with how tight the belts are. It means that the pulley is slipping on the motor shaft, so check if its grub screw properly tightened.
by josefprusa
Fri Feb 03, 2017 8:15 pm
Forum: Original Prusa i3 MK2
Topic: New 3.0.10-RC1 firmware for Prusa i3 MK2
Replies: 36
Views: 3615

Re: New 3.0.10-RC1 firmware for Prusa i3 MK2

mavu wrote:
Speaking of settings, there were some changes in the settings repo. does it make sense to import those into my settings?
They contain setting for new supports which will be introduced with new Slic3r.

Also get ready for variable layer height :-)
by josefprusa
Fri Feb 03, 2017 5:18 pm
Forum: Original Prusa i3 MK2
Topic: New 3.0.10-RC1 firmware for Prusa i3 MK2
Replies: 36
Views: 3615

Re: New 3.0.10-RC1 firmware for Prusa i3 MK2

JeffJordan wrote::?: in 3.0.10-alpha2 there was a (nice) new feature for the extruder calibration (10cm trick). has this been rejected for rc1 ? or does it simply lack in your list of changes ?
We decided to investigate more as it would probably require changes to the print settings.
by josefprusa
Mon Jan 02, 2017 3:55 pm
Forum: Original Prusa i3 MK2
Topic: Bed connector going hot
Replies: 1
Views: 501

Re: Bed connector going hot

Hi Helmi, This happens when the connector is not fully plugged in or the wire harness from the heated bed is not perfectly secured to the RAMBo cover and connector wiggle with every bed movement. This is the connector http://www.molex.com/molex/products/datasheet.jsp?part=active/0395300002_TERMINAL_...

Go to advanced search