Search found 1378 matches

Go to advanced search

by JeffJordan
Sun May 27, 2018 8:39 am
Forum: How do I print this? (Printing help)
Topic: first layer supports not sticking
Replies: 2
Views: 67

Re: first layer supports not sticking

.... I slowed down the print speed to 60, ... 60 what ? percentage setting at the printer ? with which print speed has it been sliced ? do you use linear advance settings ? for such a structure I wouldn't print faster than 30mm/s for the first few layers, without lin-ad. furthermore I would recomme...
by JeffJordan
Sun May 20, 2018 8:35 pm
Forum: Wie drucke ich das? (Hilfe zum Drucken)
Topic: Hilfe gesucht zu 3D Druckertest und Passgenaugkeit der Teile
Replies: 11
Views: 118

Re: Hilfe gesucht zu 3D Druckertest und Passgenaugkeit der Teile

Hier ein paar grundsätzliche Überlegungen zum Thema Passgenauigkeit: :idea: Man muss beim exakten Designen von Objekten die ineinander passen sollen immer mit berücksichten, dass die eingeschränkte x/y Wiederholgenauigkeit bei der Positionierung des Druckkopfes prinzipiell immer dazu führt, dass Löc...
by JeffJordan
Sun May 20, 2018 8:15 pm
Forum: Zusammenbau und Fehlersuche bei den ersten Druckversuchen
Topic: Layerverschiebung
Replies: 2
Views: 60

Re: Layerverschiebung

Ist der Layer Shift in x oder in y Richtung (also rechts/links oder vorne/hinten) ? Die Antwort auf die Frage könnte schon mal einschränken, wo man nach eventuellen losen Ritzeln oder sonstigen Problemen suchen könnte. Manchmal gibt es auch einen Layer Shift wenn du mit einer zu hohen Volumenfüllrat...
by JeffJordan
Thu May 10, 2018 6:32 am
Forum: Assembly and first prints troubleshooting
Topic: life adjust Z - my way
Replies: 352
Views: 65716

Re: life adjust Z - my way

... So I backed up and tried -.910 and -.905; both seemed pretty damn good. But for some reason -.910 was smoothest, so I've stuck with that. But still has a few rough spots. Does it sound okay? yes, sounds ok for me. if you still have a few rough spots, it might be a good idea to check the filamen...
by JeffJordan
Sun Apr 15, 2018 7:39 pm
Forum: How do I print this? (Printing help)
Topic: Print curling
Replies: 3
Views: 183

Re: Print curling

:idea: did you thoroughly clean the pei sheet with 99% isopropyl alcohol ??? or even acetone ? and didn't touch the surface with your hands before printing ? maybe your pei sheet is a little bit "worn out", so "refreshing" it with 000 steel wool might be a good idea. by the way: at the thread, where...
by JeffJordan
Sun Apr 08, 2018 2:59 pm
Forum: Assembly and first prints troubleshooting
Topic: life adjust Z - my way
Replies: 352
Views: 65716

Re: life adjust Z - my way

I recommend to "fine tune" it down to +/- 20µm. check out -920 and -940. you should get a closed and consistent surface, without seperated strains, at a thickness of 0.20mm. remember, if you still got strains but no closed surface even when lowering the tip of the nozzle much further: check and cali...
by JeffJordan
Wed Apr 04, 2018 11:20 am
Forum: Hardware, firmware and software help
Topic: extruder printed in orange, a real problem ?
Replies: 3
Views: 200

Re: extruder printed in orange, a real problem ?

waldemar.g wrote:
Wed Apr 04, 2018 11:13 am

...
print it in orange and paint the inside of the filament sensor slot with a black maker or black spray :-)
something like that was my idea so far...
:mrgreen:
Cheeres,
Jeff
by JeffJordan
Wed Apr 04, 2018 8:40 am
Forum: Hardware, firmware and software help
Topic: extruder printed in orange, a real problem ?
Replies: 3
Views: 200

extruder printed in orange, a real problem ?

Hi guys, after printing the extruder parts for the MK2(s) -> MK2.5 upgrade in orange abs, I noticed that prusa doesn't ship the upgrade anymore with orange filament. they are only going to be shipped with black petg now, due to issues with the optical filament runout sensor. is there a real problem ...
by JeffJordan
Mon Apr 02, 2018 7:43 am
Forum: Hardware, firmware and software help
Topic: Why is the extruder pulley made of Brass ?
Replies: 47
Views: 5646

Re: Why is the extruder pulley made of Brass ?

Joan is right (as usual), the brass hobbed pulleys are no longer available at the spare-parts section of the prusa shop. :roll: just noticed that because the brass pulleys of my two printers (genuine MK2 and selfmade clone) are worn out now and at my clone I get extrusion interruptions during the pr...
by JeffJordan
Fri Mar 02, 2018 1:05 pm
Forum: Assembly and first prints troubleshooting
Topic: life adjust Z - my way
Replies: 352
Views: 65716

Re: life adjust Z - my way

printingrookie wrote:
Fri Mar 02, 2018 9:39 am
... Could the extrusion multiplier be the culprit here?
yes, might be.
but even inaccuracy in the diameter of the nozzles borehole could be a reason.

Go to advanced search