Search found 2321 matches

Go to advanced search

by joan.t
Aug 15, 2018 5:34 am
Forum: Awesome prints & printing tips
Topic: Another Game Board PoC
Replies: 5
Views: 29

Re: Another Game Board PoC

:D Indeed...

and it keeps the grey matter active!

Joan
by joan.t
Aug 14, 2018 11:21 pm
Forum: Awesome prints & printing tips
Topic: Another Game Board PoC
Replies: 5
Views: 29

Re: Another Game Board PoC

Hi Ruffus,

the ovals are more difficult than say a dovetail style option what made you decide to go with ovals!?

Joan
by joan.t
Aug 14, 2018 11:18 pm
Forum: Hardware, firmware and software help
Topic: Not see any change in preview of Slic3R after changing nozzle size setting
Replies: 3
Views: 17

Re: Not see any change in preview of Slic3R after changing nozzle size setting

Hi Bruce, here are two pictures 250 micron nozzle.JPG the first shows the first layer of a model that I am printing at the moment... this copy is sliced with 0.25mm nozzle parameters 600 micron nozzle.JPG the second shows the first layer of the same model, sliced with 0.60mm nozzle parameters I thin...
by joan.t
Aug 14, 2018 10:47 pm
Forum: Awesome prints & printing tips
Topic: Another Game Board PoC
Replies: 5
Views: 29

Re: Another Game Board PoC

Good going!
have you managed to clip other parts to intersect with all sides

how many parts to create a whole game board?

how much tolerance did you include for the joints??

regards Joan
by joan.t
Aug 14, 2018 10:41 pm
Forum: Hardware, firmware and software help
Topic: Pinda hardware testing inconsistent at any given temperature
Replies: 7
Views: 92

Re: Pinda hardware testing inconsistent at any given temperature

Hi Mk3Gibbs I am interested in your tests... they could help us all. I believe the Pinda is an NPN open collector switching device so I am wondering why you are using a analogue to digital port to test it's output? surely you should be using a digital port with a pull up resistor? that would remove ...
by joan.t
Aug 14, 2018 9:23 pm
Forum: Hardware, firmware and software help
Topic: Bed not heating after years of sterling service
Replies: 6
Views: 76

Re: Bed not heating after years of sterling service

shame the fix was so expensive!

regards Joan
by joan.t
Aug 14, 2018 8:19 pm
Forum: Assembly and first prints troubleshooting
Topic: Print size is inaccurate (x and y)
Replies: 6
Views: 102

Re: Print size is inaccurate (x and y)

Hi Rams, honest enquiry... what is the working tollerance for your design? is 5/100 of a millimetre that much of an issue... if you measure the same part, the next day. is it still 5/100 of a millimetre oversize? we are using heat fused filament deposition (Posh glue gun) to make these parts if you ...
by joan.t
Aug 14, 2018 7:21 pm
Forum: General discussion, announcements and releases
Topic: Extruder squeaking caused by PTFE tube?
Replies: 3
Views: 96

Re: Extruder squeaking caused by PTFE tube?

Hi Eric, the attached picture is a generic E3D v6 cross section, Ignore the blue fan shroud and black fan E3D v6.jpg I suggest that you... Carefully, taking care not to damage the heater and particularly, the thermistor wires... unscrew the heat sink, finned bit, from the heatbreak the PTFE should s...
by joan.t
Aug 14, 2018 4:31 pm
Forum: General discussion, announcements and releases
Topic: Extend Z Axis?
Replies: 5
Views: 81

Re: Extend Z Axis?

There are a number of threads on here about maximising the z height with the existing frame. Have a search on the site. And look on thingiverse
Regards Joan.

Go to advanced search